CONFIRM THE PART FITS

Range Oven Control Board and Clock (replaces 316577077K, 5303935335) 316577077

Part #316577077

This part is no longer available.

We've permanently sold out of this part. It's no longer available from the manufacturer and the manufacturer has no substitute for this part. Although our call center staff is always happy to help when possible, they don't have access to this part. If you can't find that part and decide to replace the product, we invite you to visit www.sears.com

This part fits

Part Information

This oven control board and clock (part number 316577077) is for ranges.

Oven control board and clock 316577077 monitors the oven temperature and controls the oven heating functions in the range, and includes the digital display for the time and temperature settings.

Unplug the range or shut off the house circuit breaker for the range before installing this part. Wear work gloves to protect your hands.

Reviews

simple to install
March 08, 2021

Part was a simple replacement, Note: the packaging was horrible - I was afraid the part would be damaged, no protective wrapping at all. Box looked as if it was thrown around. Be careful removing screws (especially around burners) they rust from the heat and are fragile. you have to get to the screws under the backing to remove the casing and that required lifting the range top (which the burners are attached to) and sliding it forward just enough to get to those screws in the rear corners. the backing will not come off without removing them. you need to lift the backing to access the module connections properly

Soldier357, Pennsylvania, PA

Did you find this review helpful?

Ease of Installation
Moderate
Duration of Installation
30 minutes - 1 hour

Yes, I would recommend this to a friend

IT WORKS!
January 08, 2021

Old controller worked fine but the portions of the led readout (time/timer) had burned or shorted out. New controller is nice and bright. If you are a bit of a do-it-your-selfer this project will be okay to take on. A few screws to remove backside panel. The actual removal install of the controller had 4 screws and a few wire harnesses to plug in. Just remember where each wire attaches. Minor challenge to get at the 4 screws but you will figure it out. They are almost finger tight so getting a small socket or screwdriver onto each screw can be done without removing the top cover of the range control panel. If you are not a DIY, hire someone to do it. The replacement took 15 to 20 minutes. The whole job took 45 minutes because I ended up cleaning the back, sides, floor, cabinets and the entire oven really good. With the new controller I can read the time and timer easily. It's like a new oven!

GregO, Minnetrista, MN

1 person thought this review was helpful.

Ease of Installation
Moderate
Duration of Installation
30 minutes - 1 hour

Yes, I would recommend this to a friend

Pretty straightforward
September 23, 2020

Carefully remember the relative positioning of the metal pieces behind the control panel for re-installing. I had to remove the stove top to get at some screws important to accessing the Oven Control Board.

Yondanron, Petaluma, CA

1 person thought this review was helpful.

Ease of Installation
Moderate
Duration of Installation
30 minutes - 1 hour

Yes, I would recommend this to a friend

Perfect fit, new features
December 04, 2019

The two other posts re. this product seem to be the extremes of the installation process. It took me about an hour, most of it was messing around trying to pull the rear panels off the stove to get access to the board. Once I did, there 6 or so connections to make. It's pretty hard to screw up, but I did it one at a time to make sure everything lined up. If you can't change your own oil, or you call AAA to fix a flat tire, then you'd better call a pro. If that type of work doesn't scare you, its a pretty straight forward process to swap out the part. It's great to have all the LED segments lit up again and the board works perfectly. One note, my old one didn't report the temp of the oven during warm up. This one does - when you set the temp, it drops to 101F, and stayed there for several seconds. I thought it was a problem, but once the oven fires up, it reports the increasing temp and then works great. Neat feature for impatient chefs wondering about oven temp.

CMCguy, Undisclosed

6 people thought this review was helpful.

Ease of Installation
Moderate
Duration of Installation
30 minutes - 1 hour
I had F90 Code. Fixed Oven
December 04, 2019

Do the Trouble Shooting To Ensure This is The Part You need.

Gogo K, DFW

Did you find this review helpful?

Ease of Installation
Moderate
Duration of Installation
1 - 2 hours

Yes, I would recommend this to a friend

OEM. Board
April 23, 2018

Changing the board was straight forward. Just four 1/4" hex head screws and 4 connector plugs also the back cover with 3 screws.

retiredmike, arlington hts, IL

4 people thought this review was helpful.

Ease of Installation
Easy
Duration of Installation
30 minutes - 1 hour
NO HELP FROM SEARS PARTS DIRECT
April 10, 2018

Since I could not find any instructions in the part packaging, nor online ANYWHERE, on removing an existing surrounding part I needed to remove to install the new "Control Board", I had to improvise. I tried to call for help, but your customer service number was no help and told me to go to a Sears store. I had the correct model, and the correct part number, but your videos showed a view of a range that wasn't the same as mine. TERRIBLE experience....won't buy Sears again!

SophiaLoren, Philadelphia, PA

Did you find this review helpful?

Ease of Installation
Very Difficult
Duration of Installation
More than 2 hours