How to replace a dryer drive belt
This DIY dryer repair guide has step-by-step instructions for replacing a broken dryer belt. The dryer drive belt turns the dryer drum when the drive motor turns. If the drive belt breaks, the motor runs, but the drum won't move. You can easily check whether the drive belt is broken by lifting the top and inspecting the belt. Replace a damaged or broken drive belt with the manufacturer-approved dryer part.
The video below shows how to replace a broken drive belt in a gas dryer, but the repair steps are the same for electric dryers. This repair procedure covers Kenmore, Whirlpool, Maytag, Amana, Roper, Crosley and Estate dryers with a lint screen housing located in the top dryer panel.
This video explains how to replace a drive belt on a dryer.
Instructions
- 01.
Shut off the power
Unplug the dryer. If it's a gas dryer, shut off the gas.
Wear work gloves to protect your hands.
- 02.
Raise the top panel
Pull the lint screen out of the housing in the top panel of the dryer.
Use a Phillips screwdriver to remove the 2 screws that secure the lint screen housing to the top panel. To release the clips that lock the top of the dryer in place, push a putty knife under the lid near the left and right edges of the front of the dryer.
Lift the top and prop it securely against the wall behind the dryer.
PHOTO: Remove the lint screen.
PHOTO: Remove the lint screen housing screws.
PHOTO: Release the panel locking clips.
PHOTO: Lift the top panel.
- 03.
Remove the front panel
Use a slot screwdriver to release the locking tab on the wire harness plug for the door switch. Disconnect the wire harness.
Use a 5/16-inch nut driver to remove the front panel mounting screws from the inside of the dryer.
Pull the front panel forward slightly, and then lift and unhook it from the 2 bottom hangers.
Pull the front panel off of the dryer and set it aside.
PHOTO: Disconnect the wire harness for the door switch.
PHOTO: Remove the front panel mounting screws.
PHOTO: Remove the front panel.
- 04.
Remove the drive belt
Pull the broken belt out of the dryer.
- 05.
Install the new drive belt
Position the new drive belt on the dryer drum. Lift the front of the drum to access the drive motor and idler pulley.
Thread the drive belt through the idler pulley.
Push the idler pulley to the right and loop the drive belt over the motor pulley.
Tip: While the dryer is open, vacuum the dust and lint from inside the dryer.PHOTO: Thread the belt through the idler pulley.
- 06.
Reinstall the front panel
Position the front panel on the hangers at the bottom of the dryer.
Line up the mounting holes and reinstall the screws in the top of the front panel to secure it to the dryer.
Plug the wire harness back into the plug on the door switch. Make sure the locking tab engages properly.
- 07.
Reassemble the top panel
Lower the top panel and snap it into place.
Reinstall the screws in the lint duct housing and reinstall the lint screen.
- 08.
Restore power to the dryer
Plug the dryer into the wall outlet. If it's a gas dryer, turn on the gas supply to the dryer.
Most common symptoms to help you fix your dryers
Choose a symptom to see related dryer repairs.
Main causes: bad gas valve coils, broken heating element, tripped safety thermostat or fuse, bad operating thermostat, c…
Main causes: bad timer or electronic control board, door switch failure…
Main causes: lack of electrical power, bad power cord, wiring failure, bad control board, blown thermal fuse, bad door s…
Main causes: clogged exhaust vent, bad motor relay, loose dryer door catch, bad door switch, control system failure, fau…
Main causes: damaged door strike, worn door catch…
Main causes: bad drum support roller, damaged idler pulley, broken blower fan blade, worn drum glide bearing, bad drive …
Main causes: clogged exhaust system, heating system failure, deposits on moisture sensor, control system failure…
Main causes: door switch failure, lack of power, broken belt, blown thermal fuse, bad drive motor, control system failur…
Most common repair guides to help fix your dryers
These step-by-step repair guides will help you safely fix what’s broken on your dryer.
How to replace a thermal fuse in an electric dryer
When the air in the dryer overheats—usually because the vent is clogged—the thermal fuse blows, stopping the dryer. You …
How to install a thermal cut-off fuse kit in an electric dryer
The thermal cut-off fuse shuts off the heat if the dryer overheats when the high-limit thermostat fails. Install a ther…
How to replace a dryer door switch
The dryer won't start if the door switch isn't working correctly. You can install a replacement dryer door switch in les…
Effective articles & videos to help repair your dryers
Use the advice and tips in these articles and videos to get the most out of your dryer.
Get expert tips on using your dryer efficiently to save energy.…
Get expert DIY tips and advice for keeping your clothes dryer in top shape with cleaning and maintenance.…
Read about how you can keep you Kenmore hybrid heat pump dryer maintained.…