June 01, 2015

How to replace an oven temperature sensor on a gas range

How to replace an oven temperature sensor on a gas range

This step-by-step repair guide shows how to replace the gas oven temperature sensor on a range. The oven sensor measures the oven temperature and sends that data to the oven control board, which maintains the set oven temperature. If the oven sensor malfunctions, the oven becomes too hot or won't get hot enough. If the temperature sensor fails completely, the control panel displays an error code. Replace the gas oven temperature sensor using a manufacturer-approved gas range part.

Use this procedure to replace the oven temperature sensor in many Kenmore, Frigidaire, Whirlpool, KitchenAid, Maytag, Amana, Electrolux, GE, LG and Samsung gas ranges.

Quick links
Tools required
1/4-inch nut driver
Needle-nose pliers
Work gloves
Repair difficulty
Time required
15 minutes or less
Repair difficulty
Time required
15 minutes or less
Replacing a gas range oven temperature sensor video.

Replacing the oven temperature sensor in a gas range video.

Instructions

  1. 01.

    Shut off electrical power and the gas supply to the range

    Shut off all electricity to the range.

    Turn the gas shut-off valve to the off position. 

  2. 02.

    Remove the mounting screws

    Remove the oven racks.

    Find the temperature sensor probe in the top left corner of the back wall of the oven interior. Using a 1/4-inch nut driver, remove the 2 hex head screws from the base of the temperature sensor probe.

    Tip: If you can't complete this repair because the door gets in your way, remove the door, following instructions in your owner's manual. You might need help lifting the door off the oven. Set the door on a pad.
  3. 03.

    Access the wire connector

    Carefully pull the oven temperature sensor probe forward into the oven interior. The wires connected to the probe have enough slack that you can pull it a just few inches—far enough to disconnect the wires. As you pull, use needle-nose pliers to guide the wire harness connector through the hole in the oven wall.

    Pull the temperature sensor probe a few inches forward so you can reach the wire connector.

  4. 04.

    Disconnect the wire harness

    Holding the connector with needle-nose pliers, depress the locking tab on the plug and disconnect the plug from the sensor probe. Don't let the connector slip back through the hole, or you must remove the back panel of the oven to retrieve it.

  5. 05.

    Install the new temperature sensor probe

    While holding the connector with a pair of needle-nose pliers, snap it into the plug of the new probe. Push the wire into back wall of the oven. Position the new sensor probe and line up the holes for the mounting screws. Insert the mounting screws and tighten firmly using a nut driver.

    Tip: If the plug doesn't fit the original wire harness connector, use a wire cutter to snip off the plug and the wire harness connector. Strip the 1/2" of insulation from the wires and make the connection with ceramic wire nuts.
  6. 06.

    Restore power

    Turn on the electricity and the gas.

Warning: Undertaking repairs to appliances can be hazardous. Use the proper tools and safety equipment noted in the guide and follow all instructions. Do not proceed until you are confident that you understand all of the steps and are capable of completing the repair. Some repairs should only be performed by a qualified technician.

Most common symptoms to help you fix your ranges

Choose a symptom to see related range repairs.

Main causes: broken oven door lock assembly, wiring failure, electronic control board problem…

Main causes: broken broiler element, weak or broken broil burner igniter, control system failure, faulty temperature sen…

Main causes: power supply problem, control thermostat or electronic control board failure, broken element, bad burner ig…

Main causes: bad bake element, broken burner igniter, control system failure, blown thermal fuse, faulty temperature sen…

Main causes: food splatters, spilling food on the oven door, allowing liquid to drip through oven door vent when cleanin…

Main causes: faulty temperature sensor, electronic control board problem, control thermostat failure, weak burner ignite…

Main causes: power supply failure, blown thermal fuse, bad relay control board, damaged terminal block, wiring failure…

Most common repair guides to help fix your ranges

These step-by-step repair guides will help you safely fix what’s broken on your range.

How to replace a range oven door switch

How to replace a range oven door switch

The oven door switch detects whether the oven door is closed and helps control the oven light. Replace the switch if it …

Repair difficulty
Time required
 30 minutes or less
How to replace a range oven door lock assembly

How to replace a range oven door lock assembly

Oven door not locking? You can replace the lock assembly in less than 30 minutes. Here's how.…

Repair difficulty
Time required
 15 minutes or less

Effective articles & videos to help repair your ranges

Use the advice and tips in these articles and videos to get the most out of your range.

How to clean and maintain your stove

How to clean and maintain your stove

Learn how to clean and maintain your stove to keep it in top shape.…

How to enjoy all the online benefits we offer on our Sears PartsDirect website

How to enjoy all the online benefits we offer on our Sears PartsDirect website

Learn about all the convenient features on our Sears PartsDirect website that make your parts purchases easier.…

Top questions about Sears and Sears PartsDirect

Top questions about Sears and Sears PartsDirect

Get answers to frequently asked questions about Sears and Sears PartsDirect.…