How to replace the user interface board in a front-load washer
This step-by-step washer repair guide explains how to replace the user interface control board in the control panel of a front-load washer. The user interface board holds the display lights and buttons you press when selecting the washer's cycles and settings. If a control button or display light on the control panel won't work because of a failed user interface board, replace it with a manufacturer-approved replacement part.
Use the steps in this guide to replace the user interface board in Kenmore and LG front load washers. You also can use the same basic procedure to replace the user interface board in some Samsung, Whirlpool, Maytag, Amana, Frigidaire and GE front-load washers.
Instructions
- 01.
Shut off the electricity
Unplug the power cord from the wall outlet.
Wear work gloves to protect your hands.
Have someone help you move the washer away from the wall.
- 02.
Remove the top panel from the washer
Remove the 2 screws on the back of the washer that hold the top panel.
Pull the top panel toward the rear of the washer and lift it up and off.
PHOTO: Remove the 2 screws from the back of the top panel.
PHOTO: Remove the washer top panel.
- 03.
Remove the screw on the back of the control panel
Using a Phillips screwdriver, remove the screw on the back of the control panel.
The screw is on the right side as you face the front of the washer.
PHOTO: Remove the screw on the back of the control panel.
- 04.
Remove the screws in the dispenser drawer housing
Pull the dispenser drawer forward until it stops.
Release the locking tab at the back of the dispenser drawer and then pull it completely out of the dispenser housing.
Using a Phillips screwdriver, remove the screws on each side of the dispenser housing.
PHOTO: Pull the dispenser drawer out.
PHOTO: Release the dispenser drawer.
PHOTO: Remove the screws from each side of the dispenser housing.
- 05.
Remove the control panel
Unplug the wire harness connections for the control panel by pressing on the release tabs and sliding the connectors apart.
Stand in front of the washer and lift up on the control panel to release the top. Pull the control panel off the washer.
PHOTO: Disconnect the control panel wires.
PHOTO: Pull the control panel off the washer.
- 06.
Remove the user interface board
Remove the screws that secure the user interface board in the control panel.
Pull the user interface board out.
PHOTO: Mounting screws in the user interface board.
PHOTO: Remove the screws that hold the user interface board.
PHOTO: Remove the user interface board from the washer.
- 07.
Install the new user interface board
Place the new interface control boards into the control panel and install the screws loosely.
Make sure that all the buttons are lined and can depress the switches on the interface board when you push the buttons.
Carefully tighten the mounting screws.
- 08.
Reinstall the control panel
Position the control panel on the top of the front panel.
Reinstall the screws in the dispenser housing.
Reinstall the screw on the back right side of the control panel.
Plug in the wire harness connections for the control panel.
Push the detergent dispenser back into the drawer housing.
PHOTO: Position the control panel on the top of the front panel.
PHOTO: Reinstall the screws on each side of the dispenser housing.
PHOTO: Reinstall the screw on the right side of the control panel.
PHOTO: Plug in the control panel wire harness connections.
- 09.
Reinstall the top panel
Push the panel down and forward to seat it on the washer frame.
Reinstall the screws to secure the back panel. Avoid overtightening.
- 10.
Restore the power
Plug the washer into the electrical outlet.
Return the washer to its original location.
Most common symptoms to help you fix your washers
Choose a symptom to see related washer repairs.
Main causes: broken lid switch or lid lock, bad pressure switch, broken shifter assembly, faulty control system…
Main causes: lack of electrical power, wiring failure, bad power cord, electronic control board failure, bad user interf…
Main causes: leaky water inlet valve, faulty water-level pressure switch, bad electronic control board…
Main causes: water heater failure, bad water temperature switch, faulty control board, bad water valve, faulty water tem…
Main causes: no water supply, bad water valves, water-level pressure switch failure, control system failure, bad door lo…
Main causes: worn agitator dogs, bad clutch, broken motor coupler, shifter assembly failure, broken door lock, suspensio…
Main causes: unbalanced load, loose spanner nut, worn drive block, broken shock absorber or suspension spring, debris in…
Main causes: clogged drain hose, house drain clogged, bad drain pump, water-level pressure switch failure, bad control b…
Main causes: bad lid switch or door lock, bad timer or electronic control board, wiring failure, bad water inlet valve a…
Repair guides for front-load washers
How to replace a water inlet valve on a front-load washer
The water valve assembly is the gatekeeper for water entering your front-load washer. You can replace it yourself, follo…
How to replace a motor control board on a front-load washer
The motor control board makes sure the motor spins in the right direction and at the right speed. You can install a new …
How to replace the user interface board in a front-load washer
Follow these steps to replace the user interface board in your front-load washer if the buttons or lights are broken.…
Effective articles & videos to help repair your washers
Use the advice and tips in these articles and videos to get the most out of your washer.
Find tips for using your washing machine efficiently to save energy and help reduce utility bills.…
Get answers to frequently asked questions about Sears and Sears PartsDirect.…
Learn how to repair broken, frayed or damaged wires in your appliances.…