- Kenmore refrigerator water filters
- Whirlpool refrigerator water filters
- Samsung refrigerator water filters
- GE refrigerator water filters
- LG refrigerator water filters
- Frigidaire refrigerator water filters
- KitchenAid refrigerator water filters
- Maytag refrigerator water filters
- Kenmore Elite refrigerator water filters
- Estate refrigerator water filters
- GE Profile refrigerator water filters
- Amana refrigerator water filters
- Bosch refrigerator water filters
- Dacor refrigerator water filters
- Electrolux refrigerator water filters
CONFIRM THE PART FITS
Snowblower Bottom Guard Panel (replaces 1501055E701, 1501311E701MA, 722067A, 722067ASM, MT1501055E701MA) 1501055E701MA
Part #1501055E701MA
Online Only Price
$52.68 |
10% OFF Phone Price : $58.68
In Stock
For ZIP codes near Edit
This part fits
Previous part numbers
Part #MT1501055E701MA
Part #722067ASM
Part #1501055-853
Part #1501055E701
Part #722067A
Part Information
This bottom guard panel (part number 1501055E701MA) is for snowblowers.
Bottom guard panel 1501055E701MA fits under the snowblower to cover and protect the drive chains, friction disc and friction wheel.
Wear work gloves to protect your hands when installing this part.
Top models using the same part
| Model Name | Model Number | Diagram Name |
|---|---|---|
| Model #1694993 Snapper gas snowblower | 1694993 | Engine/frame-ce models |
| Model #E115328E (1695096) Snapper gas snowblower | E115328E (1695096) | Engine/frame-ce models |
| Model #1694994 Snapper gas snowblower | 1694994 | Engine/frame-ce models |
| Model #E95288E (1695094) Snapper gas snowblower | E95288E (1695094) | Engine/frame-ce models |
| Model #1695096 Snapper gas snowblower | 1695096 | Engine/frame-ce models |
| Model #E85268E (1695093) Snapper gas snowblower | E85268E (1695093) | Engine/frame-ce models |
| Model #1695094 Snapper gas snowblower | 1695094 | Engine/frame-ce models |
| Model #1694996 Snapper gas snowblower | 1694996 | Engine/frame-ce models |
| Model #E105308E (1695095) Snapper gas snowblower | E105308E (1695095) | Engine/frame-ce models |
| Model #95288E (1694994) Snapper gas snowblower | 95288E (1694994) | Engine/frame-ce models |
Reviews
Easy to install. Fits exactly as it should.
Easy to install took about 20 minutes. All holes lined up perfectly.
Patricia, Mahanoy City, PA
Did you find this review helpful?
- Ease of Installation
- Very Easy
- Duration of Installation
- Less than 30 minutes
Yes, I would recommend this to a friend
Easy to Install
Easy to install and perfect match for my equipment
Boli, Easton PA
Did you find this review helpful?
- Ease of Installation
- Very Easy
- Duration of Installation
- Less than 30 minutes
Yes, I would recommend this to a friend
For perfect
It was relatively easy to install. The only issue was the current screws were rusted and need a shot of liquid wrench.
Jersey J, 7463
Did you find this review helpful?
- Ease of Installation
- Moderate
- Duration of Installation
- 30 minutes - 1 hour
Yes, I would recommend this to a friend
Bottom guard could have been better designed
The metal forming the front slots is too thin and narrow, so rust out too soon, leaving no front support for the pan. This is my third bottom guard, the prior two having both lost all front support. I also, this time, had to replace all the bolts holding it on since half the bolt holes had stripped, so would no longer tighten. The back was also not bent at the correct angle for the tabs to engage. I bought it, am using it, but the whole bottom design was not well thought out, especially since the sheer pin that breaks most often is inside it.
Blarfnitz, Maine
Did you find this review helpful?
- Ease of Installation
- Moderate
- Duration of Installation
- 1 - 2 hours
Yes, I would recommend this to a friend
snowblower bottom cover
this bottom cover for my older snowblower fit like a charm. I was amazed the piece was still offered. price wasn't too bad either.
paulbert, North Liberty, IA
Did you find this review helpful?
- Ease of Installation
- Very Easy
- Duration of Installation
- Less than 30 minutes
Yes, I would recommend this to a friend
Takes little time to instal
Part was easy to install and took less then 20 minutes. Removed the old plate and installed the new.
Slimey, NE
Did you find this review helpful?
- Ease of Installation
- Very Easy
- Duration of Installation
- Less than 30 minutes
Very simple with one little hint!
Once blower is up on it's nose,remove all four of the bolts (easily available for about 50' each at your hardware store) and feed the three tabs on the panel into the slots - insert the bolts. Holding the panel it's proper place feed the other two bolts. Into appropriate holes. Tighten bolts, you're done.
Berr40, Western MA
Did you find this review helpful?
- Ease of Installation
- Very Easy
- Duration of Installation
- Less than 30 minutes
snow blower parts
the part was an exact duplicate of the original and fit without any problems
scantech, connecticut
Did you find this review helpful?
- Ease of Installation
- Easy
- Duration of Installation
- 30 minutes - 1 hour