Whirlpool belt-drive top-load washer error codes

Use only HE (High Efficiency) detergent. Reduce the quantity of detergent to prevent excessive suds.

Make sure that fill hoses are properly connected. Check the resistance of the thermistor (temperature sensor). It should measure around 50K ohms (50,000 ohms) at 77 degrees. If the thermistor is defective, replace it.

Re-distribute the load inside the spin basket. If that doesn't help, then check the suspension rods and springs. If a suspension rod and spring is broken or damaged, replace all of the suspension rods and springs (the replacement part is a kit that has all 4 rods/springs).

Unplug the washer. Check the wiring connections on the main electronic control board in the console. If the wiring connections are okay, then the main electronic control board will normally need to be replaced.

Unplug the washer. Check the wiring connections on the main electronic control board and the drive motor. If the wiring connections are okay, then the drive motor windings will need to be checked for resistance. If the drive motor is bad, replace it. If the drive motor is okay, the main electronic control board will normally need to be replaced.

This code is for models with a digital display. One or more keys on the user interface were actuated for 15 seconds or longer. If a key is stuck and cannot be freed up then the user interface control will need to be replaced.

This code is for models with a digital display. It normally occurs when an incompatible control component (Main Electronic Control board or User Interface control) is replaced in the console. Check the replacement part numbers and reorder the correct part.

Unplug the washer. Check the air hose connection between the bottom of the tub and the water level pressure switch in the console. If no problems are found, then the main electronic control board (which includes the water level pressure switch) will normally need to be replaced.

Unplug the washer. Open the console and check the resistance through the thermistor circuit (black wires). It should measure around 50K ohms (50,000 ohms) at room temperature. If the thermistor is defective, replace it (the thermistor is a component in the inlet valve assembly wiring harness).

This code is displayed if Start is pressed with the lid open. If the lid switch on the lid lock/switch assembly isn't detecting the condition of the washer lid properly, then the lid lock/switch assembly will need to be replaced.

Unplug the washer. Check the lid lock/switch assembly for debris or an item that is interfering with the lock strike being engaged by the lid lock mechanism. If no interference is apparent, then the lid lock/switch assembly will normally need to be replaced.

Unplug the washer. Lift the top panel of the washer to access the lid lock/switch assembly. Try to manually unlock the washer lid without breaking the lid lock/switch assembly and the lock strike. If the components are damaged, replace them. If the lid lock/switch assembly won't lock and unlock properly, replace it.

If the washer is started several times without the lid ever being opened, then this code appears. If the lid is actually being opened between cycles but the control does not detect it, then the door lock/switch assembly will normally need to be replaced.

See if the spin basket rotates freely. If not, then examine and replace any defective drive components. If the basket spins properly, unplug the washer and check the wiring connections on the shifter assembly. That component has the optical tachometer. If the wiring connections are okay, then that shifter assembly will normally need to be replaced.

The main electronic control board cannot determine the position of the drive system shifter. Unplug the washer and check the wiring harness connections on the main electronic control board and the shifter assembly. If the wiring connections are okay, then the shifter assembly will normally need to be replaced.

Unplug the washer and check the wiring connections on the drive motor. If the wiring connections are okay, then the drive motor will normally need to be replaced.

Rotate the spin basket to see if it spins freely. If not, then a garment could be stuck between the outer tub and the spin basket. A problem with drive components could also cause excess friction. Inspect the drive components and replace parts as needed.

Water isn't being detected as entering the washer. If the washer isn't filling, check the water supply faucets behind the washer to make sure that they are fully open. Check the fill hoses and inlet water valves. If the inlet water valve assembly is defective, replace it. If water is entering the machine but not being detected, then the main electronic control board (which includes the water level pressure switch) will normally need to be replaced.

If the washer is overfilling, check the inlet water valves. If the valves are not shutting off water flow, then replace the inlet water valve assembly. If the washer isn't actually overflowing, then the main electronic control board (which includes the water level pressure switch) will normally need to be replaced.

Check the fill hoses. If they are connected properly then the inlet water thermistor (temperature sensor) will probably need to be replaced. That component is part of the Inlet Water Valve Wire Harness.

The washer isn't draining after the drain pump runs for 10 minutes. Check the washer drain and the drain hose for clogs or restrictions. If the drain path is clear, unplug the washer and check the drain pump. If the drain pump is defective, replace it.

Water isn't being detected as entering the washer. If the washer isn't filling, check the water supply faucets behind the washer to make sure that they are fully open. Check the fill hoses and inlet water valves. If the inlet water valve assembly is defective, replace it. If water is entering the machine but not being detected, then the main electronic control board (which includes the water level pressure switch) will normally need to be replaced.

The washer did not drain after the drain pump has been running for 10 minutes. Check the washer drain and the drain hose for clogs or restrictions. If the drain path is clear, unplug the washer and check the drain pump. If the drain pump is defective, replace it.