How to replace the drain pump in a top-load washer
This step-by-step washer repair guide shows how to replace the drain pump in a top-load washer. If your washer won't drain, first check the washer drain for a clog and the washer drain hose for a kink—don't skip this basic troubleshooting step. If the drain and drain hose are clear, replace the drain pump with a manufacturer-approved washer part if the pump runs but doesn't pump out the water, or if it doesn't run at all because the motor no longer works.
This repair procedure is for Kenmore, Whirlpool, Maytag and Amana top-load washers. Use the same basic steps to replace the drain pump in Samsung, LG, Frigidaire and GE top-load washers.
We also have instructions for replacing the drain pump on a front-load washer.
This video shows how to replace the drain pump in a top-load washing machine.
Instructions
- 01.
Shut off the electricity and water
Unplug the power cord from the wall outlet. Turn off the water supply valves for the washer.
Wear work gloves to protect your hands.
Have someone help you move the washer away from the wall.
- 02.
Disconnect the hoses
Mark which fill hose goes to the hot connector and which goes to the cold.
Using channel lock pliers, carefully loosen and remove both fill hoses. Expect some water to pour out.
Pull the drain hose out of the standpipe behind the washer. Expect some water to pour out.
Tip: Wipe up water spills with a towel to prevent slipping.
PHOTO: Disconnect the hoses from the back of the washer.
- 03.
Carefully lay the washer on its front panel
Move the washer to an area where you can work on it.
Lay cardboard or towels in front of the washer to prevent scratching the front of the washer.
Carefully tilt the washer forward and lay it on the front panel so that you can access the drain pump from the bottom of the washer.
PHOTO: Lay the washer down on its front panel.
- 04.
Remove the drain pump
Use pliers to release the spring clamp on the drain hose.
Pull the drain hose off the drain pump.
Open the cover that protects the wire harness plug on the drain pump.
Pull the wire harness plug out of the receptacle on the drain pump.
Remove the 3 bolts that secure the drain pump to the bottom of the washer tub.
Pull the pump off and set it aside for disposal.
PHOTO: Release the drain hose spring clamp.
PHOTO: Pull the drain hose off the drain pump. Pull the drain hose off of the drain pump.
PHOTO: Open the wire harness plug cover.
PHOTO: Disconnect the wire harness from the drain pump.
PHOTO: Remove the drain pump bolts.
PHOTO: Remove the drain pump.
- 05.
Install the new drain pump
Position the new drain pump on the bottom of the washer and secure it using the 3 bolts.
Plug the wire harness into the receptacle on the new pump.
Close the cover on the wire harness connection. Push the drain hose back onto the outlet of the drain pump.
Secure it with the spring clamp.
- 06.
Set the washer upright
Carefully set the washer upright and move it close enough to the fill hoses that you can reconnect them.
- 07.
Reinstall the fill hoses
Thread the fill hoses onto the connections on the back of the washer.
Tighten the connections firmly using a pair of channel lock pliers.
- 08.
Restore the water and power
Turn on the water supply valves.
Tighten the connection if you find a slight leak. Plug the washer into the electrical outlet.
Return the washer to its original location.
Most common symptoms to help you fix your washers
Choose a symptom to see related washer repairs.
Main causes: unbalanced load, loose spanner nut, worn drive block, broken shock absorber or suspension spring, debris in…
Main causes: bad lid switch or door lock, bad timer or electronic control board, wiring failure, bad water inlet valve a…
Main causes: clogged drain hose, house drain clogged, bad drain pump, water-level pressure switch failure, bad control b…
Main causes: leaky water inlet valve, faulty water-level pressure switch, bad electronic control board…
Main causes: water heater failure, bad water temperature switch, faulty control board, bad water valve, faulty water tem…
Main causes: lack of electrical power, wiring failure, bad power cord, electronic control board failure, bad user interf…
Main causes: no water supply, bad water valves, water-level pressure switch failure, control system failure, bad door lo…
Main causes: worn agitator dogs, bad clutch, broken motor coupler, shifter assembly failure, broken door lock, suspensio…
Main causes: broken lid switch or lid lock, bad pressure switch, broken shifter assembly, faulty control system…
Repair guides for top-load washers
How to replace the clutch assembly in a top-load washer
If the washer spins when the basket is empty but not when the basket is full, the problem could be the clutch assembly. …
How to replace the motor coupler on a top-load washer
If the washer drains but won’t agitate or spin, the motor coupler might have broken to protect the drive motor from dama…
How to replace the gear case in a top-load washer
If the washer won't spin or agitate with the motor running, replace the gear case, following the steps in this repair gu…
Effective articles & videos to help repair your washers
Use the advice and tips in these articles and videos to get the most out of your washer.
Find tips for using your washing machine efficiently to save energy and help reduce utility bills.…
Learn about all the convenient features on our Sears PartsDirect website that make your parts purchases easier.…
Get answers to frequently asked questions about Sears and Sears PartsDirect.…