How to adjust a table saw blade
This DIY repair guide explains how to adjust the blade alignment on a table saw. The blade should be parallel to the miter gauge groove to make perfect cuts. Follow these steps to adjust the alignment of the table saw blade.
Follow the steps in this repair guide and video to adjust the blade alignment on common Craftsman, Mastercraft, Tradesman, Companion, DeWalt and Ryobi table saws.
This video explains how to adjust the blade on a table saw.
Instructions
- 01.
Shut off the electricity
Unplug the table saw’s power cord from the wall outlet.
- 02.
Remove the blade guard
Raise the blade to its highest cutting position.
Push the red button on the blade guard and lift off the blade guard assembly.
PHOTO: Raise the blade.
PHOTO: Remove the blade guard.
- 03.
Mark the blade
Loosen the bevel lock, set the blade to 90-degrees (straight up), and then tighten the bevel lock handle.
Mark the right side of one blade tooth using a felt-tip marker.
Rotate the marked blade tooth so that it's 1/2 inch above the table at the front of the blade.
PHOTO: Set the blade to 90-degrees.
PHOTO: Mark one blade tooth.
- 04.
Set up the combination square
Place the base of the combination square in the right side miter gauge groove.
Adjust combination square to that the ruler tip touches the marked blade tooth and lock the ruler.
PHOTO: Place the combination square in the miter groove.
PHOTO: Adjust the ruler tip to touch the marked tooth.
- 05.
Check the blade alignment
Rotate the blade to bring the marked tooth to one-half of an inch above the table at the rear of the blade.
Slide the combination square to the rear of the blade and determine the direction and degree of misalignment.
PHOTO: Slide the square to the rear.
- 06.
Adjust the blade
If the blade is partial to the right side, turn the left adjustment screw counterclockwise and the right adjustment screw clockwise to align the blade.
If the blade is partial to the left side, turn the right adjustment screw counterclockwise and the left adjustment screw clockwise to align the blade.
Recheck the blade alignment and adjust the blade until its parallel.
PHOTO: Turn the blade adjustment screws.
- 07.
Reinstall the blade guard
Push the red release button on the blade guard and reinstall the blade guard assembly on the riving knife. Release the red button.
PHOTO: Reinstall the blade guard.
- 08.
Restore power
Plug the table saw into the electrical outlet.
Symptoms for table saws
Choose a symptom to see related table saw repairs.
Main causes: lack of power, broken on/off switch, bad motor overload, broken power cord, bad drive motor...
Main causes: dirty saw blade, dull or damaged saw blade, blade alignment needs adjustment...
Main causes: saw dust build up, blade elevating and tilting mechanisms need lubrication...
Main causes: worn motor brushes, faulty drive motor, using an improper extension cord...
Main causes: blade alignment needs adjustment, worn blade, bevel positive stops need adjustments, bevel pointer needs ad...
Main causes: worn motor brushes, bad drive motor, faulty overload switch, using an improper extension cord, binding saw ...
Repair guides for table saws
These step-by-step repair guides will help you safely fix what’s broken on your table saw.
How to replace a table saw drive motor
You can replace a table saw drive motor that is weak or won't run. Here’s how....
How to adjust a table saw blade
If the table saw isn’t cutting parallel to the miter gauge groove, adjust the cutting blade following the instructions i...
How to replace a table saw motor brush set
Worn motor brushes can make the table saw motor run weak. Here’s how to replace them. ...
Articles and videos for table saws
Use the advice and tips in these articles to get the most out of your table saw.
Learn about all the convenient features on our Sears PartsDirect website that make your parts purchases easier....
Get answers to frequently asked questions about Sears and Sears PartsDirect....
Learn some of the basic rules for safely operating a table saw....