How to replace a dishwasher diverter motor
This DIY repair guide gives step-by-step instructions for replacing the dishwasher diverter motor. The diverter motor moves the diverter disc into position so the disc can direct water through the upper spray arms. If the diverter motor fails, the dishwasher stops and signals an error code. Replace the diverter motor with a manufacturer-approved dishwasher part if the error code indicates that the diverter motor failed.
This procedure is for Kenmore, Whirlpool, KitchenAid, Amana, JennAir and Maytag dishwashers.
How to replace a dishwasher diverter motor video.
Instructions
- 01.
Shut off electrical power and water supply to the dishwasher
Unplug the dishwasher or shut off the house circuit breaker for the dishwasher.
To verify that power is disconnected, make sure the control panel doesn’t light up when you press a control button or the power button.
Find the water supply valve for the dishwasher under the sink (or in the basement). Close the valve to shut off the water supply going to the dishwasher.
PHOTO: Shut off the house circuit breaker.
- 02.
Remove the diverter disc
Open the dishwasher door and pull out the bottom dishrack.
Release the upper dishrack track stops and pull out the upper dishrack.
Release and remove the bottom spray arm.
If your dishwasher is a Kenmore with the TurboZone sprayer, release and remove the TurboZone manifold.
Release the feed tube clips. Release the feed tube from the pump outlet and pull out the feed tube.
Release the locking tab and slightly rotate the pump outlet left, and then remove it.
Pull the diverter disc off the motor shaft and shut the dishwasher door.
PHOTO: Remove the diverter disc.
- 03.
Remove the bottom front access panel and toe panel
Using a nut driver, remove the screws that hold the bottom front access panel and toe panel in place.
Pull the access panel and the toe panel forward and remove them.
PHOTO: Remove the bottom toe panel.
- 04.
Pull out the dishwasher
Position the dishwasher’s power cord so it moves freely as you pull the dishwasher out from under the counter. (See Tip if your dishwasher doesn’t have a power cord.)
Place a towel under the water supply line connection. Disconnect the water supply line from the water inlet valve and wipe up spills.
Disconnect the drain line from the garbage disposal or sink drain.
Remove the 2 mounting screws from the brackets that secure the dishwasher in the cabinet opening.
Pull the dishwasher out from under the counter.
PHOTO: Disconnect the water supply line from the inlet valve.
- 05.
Remove the diverter motor
Carefully lay the dishwasher on its back to access the diverter motor.
Release and remove the wire harness connections from the diverter motor.
Remove the Torx mounting screws from the diverter motor.
Release the locking tab and pull the diverter motor out.
PHOTO: Remove the diverter motor.
- 06.
Install the new diverter motor
Push the new diverter motor onto the tub and engage the locking tab.
Install the mounting screws and connect the wire harnesses to the diverter motor.
PHOTO: Install the new diverter motor.
- 07.
Reinstall the dishwasher
Tilt the dishwasher upright and carefully push the dishwasher under the counter.
Reconnect the drain hose to the garbage disposal or sink drain.
Reconnect the water fill line to the inlet water valve.
Insert the screws into the mounting brackets that secure the dishwasher under the counter and tighten the screws.
Position the toe panel on the dishwasher and then position the access panel in front of the toe panel. Insert and firmly tighten the mounting screws.
Tip: If the dishwasher hardwires into a junction box, push the power cable into the junction box and reinstall the strain relief nut. Reconnect the wires in the junction box and reinstall the junction box cover.PHOTO: Reinstall the toe panel.
- 08.
Reinstall the diverter disc
Open the dishwasher door and reinstall the diverter disc on the keyed diverter motor shaft.
Line up the pump outlet and push it into the opening. Rotate it slightly right to engage the locking tab and lock the pump outlet into place.
Reinstall the feed tube and snap it into the mounting clips.
If you have a Kenmore dishwasher with a TurboZone sprayer, reinstall the TurboZone manifold.
Reinstall the bottom spray arm.
Push the upper dishrack into the tracks and reinstall the track stops.
Put the lower dishrack into the tub.
PHOTO: Reinstall the dishwasher diverter disc.
- 09.
Restore electrical power and the water supply
Reset the house circuit breaker or plug in the dishwasher to restore electrical power.
Open the water supply valve.
Most common symptoms to help you fix your dishwashers
Choose a symptom to see related dishwasher repairs.
Main causes: water supply problem, stuck overfill float, clogged water inlet valve screen, water inlet valve failure...
Main causes: clogged kitchen sink drain, clogged drain hose, drain check valve damaged, drain pump failure, control syst...
Main causes: broken door spring, damaged or broken door hinge...
Main cause: damaged rack height adjuster...
Main causes: improper loading, low water temperature, improper detergent dosage, detergent dispenser failure, spray arm ...
Main causes: light switch beside the sink turned off, lack of power, bad dishwasher door switch, control system failure,...
Main causes: not using rinse aid, rinse aid dispenser failure, broken heating element, malfunctioning vent, drying fan f...
Main causes: broken door latch, tripped circuit breaker, broken heating element, faulty vent fan, sensor failure, contro...
Main causes: glass or popcorn kernel stuck in the chopper blade, drain line vibrating against the cabinet, debris in was...
Most common repair guides to help fix your dishwashers
These step-by-step repair guides will help you safely fix what’s broken on your dishwasher.
How to replace a dishwasher heating element
Dishes not drying as fast as they should? The dishwasher heating element could be on the fritz. Here's how to install a ...
How to replace a dishwasher high-limit thermostat
Follow these steps to replace the high-limit thermostat in your dishwasher if prevents the heating element from heating....
How to replace a dishwasher diverter motor
Upper spray arms not getting water? The diverter motor could be broken. Use this guide to replace it....
Effective articles & videos to help repair your dishwashers
Use the advice and tips in these articles and videos to get the most out of your dishwasher.
Get tips on completing essential holiday cleaning tasks to brighten your home....
Learn about all the convenient features on our Sears PartsDirect website that make your parts purchases easier....
Get answers to frequently asked questions about Sears and Sears PartsDirect....