How to replace a freezer electronic control board
This DIY repair guide explains how to replace an electronic control board in a freezer. The electronic control board starts and stops the compressor and fans to maintain the freezer temperature.
Because other parts can also affect the operation of the fans and compressor, have a local freezer repair expert test the board to confirm it's the problem. Replace the electronic control board with the manufacturer-approved freestanding freezer part.
This repair guide and video shows how to replace the electronic control board in Kenmore, Frigidaire, Crosley, Gibson, and Kelvinator upright freezers.
Replaing a freezer electronic control board video.
Instructions
- 01.
Disconnect the electrical power
Unplug the freezer or shut off the circuit breaker for the freezer.
Tip: Move highly perishable food to a cooler or other cooled space. The freezer will be without power for about 45 minutes, which shouldn't affect most frozen foods. - 02.
Remove the front grille
Remove the screws holding the grille at the base of the freezer and pull the grille off.
PHOTO: Remove the grille screws.
PHOTO: Remove the grille.
- 03.
Remove the rear machine compartment cover
Move the freezer away from the wall.
Remove the rear machine compartment cover screws and pull off the cover.
Warning: The freezer is heavy. Use a helper to move the freezer away from the wall.
PHOTO: Remove the rear cover screws.
PHOTO: Remove the rear cover.
- 04.
Remove the electronic control
Remove the screw from the electronic control board cover.
Pull out the electronic control board cover and release it from the cabinet base. The electronic control board wires are still connected.
Set the electronic control board on the floor just behind the grill.
From the front of the freezer, pull the electronic control board through the grill opening.
Release the wire harness latch on the notch in electronic control board cover.
Take a digital picture of the wire connections on the control board before disconnecting.
Disconnect the wires from the electronic control board.
Release the locking tabs and remove the electronic control board from the cover.
Warning: Sharp, crimped tubing is exposed in the machine compartment. Place tape over the tips of exposed copper tips to protect your arms before reaching into the machine compartment.
PHOTO: Tape sharp tips of copper tubing to prevent scratching your arm.
PHOTO: Remove the control board housing screw.
PHOTO: Pull the control board out.
PHOTO: Release the wire harness locking tab.
PHOTO: Disconnect all wires from the control board.
- 05.
Install the new electronic control board
Carefully push the new electronic control board into the cover and snap it into place.
Reinstall the wire harness in the notch of the electronic control board cover and snap the wire harness latch closed.
Reconnect the wires on the electronic control board, using your digital picture as a guide.
Push the electronic control board and cover carefully into the bottom of the cabinet through the grill opening.
Mount the electronic control board cover to the base of the freezer.
PHOTO: Connect the wires and push the control board into the cabinet.
PHOTO: Mount the control board to the base of the cabinet.
- 06.
Reassemble the covers
Place the rear machine compartment cover on the back of the freezer and reinstall the mounting screws.
Reinstall the front grille.
PHOTO: Reinstall the rear cover.
PHOTO: Reinstall the grille.
- 07.
Restore electrical power
Plug in the freezer or turn on the house circuit breaker to restore power.
Most common symptoms to help you fix your freestanding freezers
Choose a symptom to see related freezer repairs.
Main causes: lack of power, bad compressor, refrigerant leak, bad thermistor, defrost system failure, dirty condenser co…
Main causes: burned out light bulb, bad door or lid switch, faulty LED light board, wiring failure, control system failu…
Main causes: compressor failure, no refrigerant, faulty sensor, control failure, broken defrost heater, bad defrost bi-m…
Main causes: damaged door or lid gasket, cracked cabinet liner, bad defrost bi-metal thermostat, broken defrost heater, …
Main causes: dirty condenser coils, condenser fan failure, dirty bottom front grill, leaky door or lid gasket…
Main causes: excessive frost, bad defrost heater, bad defrost bi-metal, control system failure, low refrigerant charge, …
Main causes: lack of power, control system failure, broken compressor start relay, locked up compressor, compressor moto…
Main causes: leaky door or lid gasket, broken defrost heater, bad defrost bi-metal thermostat, defrost control failure, …
Repair guides for upright freezers
How to replace a freezer door switch
When the door switch fails, the freezer can’t detect that the door is closed. Follow the steps in this repair guide to r…
How to replace a freezer thermistor
When the thermistor can’t sense the freezer temperature, the freezer is colder or warmer than the set temperature. Follo…
How to replace a freezer evaporator fan
Air won’t circulate to cool the freezer properly when the evaporator fan fails. Follow these step-by-step instructions t…
Effective articles & videos to help repair your freestanding freezers
Use the advice and tips in these articles and videos to get the most out of your freezer.
Learn about all the convenient features on our Sears PartsDirect website that make your parts purchases easier.…
Get answers to frequently asked questions about Sears and Sears PartsDirect.…
Benefit from other people's experience by checking on these frequently asked questions about freezers.…