August 01, 2014

How to replace a thermal fuse in an electric dryer

How to replace a thermal fuse in an electric dryer

This step-by-step dryer repair guide shows how to replace the thermal fuse for an electric dryer. The thermal fuse in a dryer is a safety component that trips if the air flowing through the drum overheats. A blocked exhaust vent is the most common reason the air overheats. When the thermal fuse blows in an electric dryer, the display lights still work but the drive motor won't run. You can't reset the thermal fuse; if it's blown, replace it with the manufacturer-approved dryer part.

Find the dryer thermal fuse location in a common dryer by watching the repair procedure in the video below. Complete the thermal fuse replacement yourself and get your dryer going again.

These steps work for replacing the electric dryer thermal fuse for Kenmore, Whirlpool, Maytag, Amana, Roper, Crosley and Estate models with a lint screen housing located in the top dryer panel.

We also have instructions for thermal fuse replacement in a gas dryer.

Quick links
Tools required
1/4-inch nut driver
Slot screwdriver
Vacuum cleaner or shop vac
Duct cleaning brush
Work gloves
Repair difficulty
Time required
15 minutes or less
Repair difficulty
Time required
15 minutes or less
Replacing a thermal fuse in an electric dryer

This video explains how to replace the thermal fuse in an electric dryer.

Instructions

  1. 01.

    Shut off the power

    Unplug the dryer to disconnect electrical power.

  2. 02.

    Remove the back panel

    Move the dryer forward and use a 1/4-inch nut driver to remove the screws from the back panel. Remove the back panel from the dryer and set it aside.

    Tip: While you have the back of the cabinet open, vacuum lint and dust from the cabinet.
    PHOTO: Remove the back panel screws.

    PHOTO: Remove the back panel screws.

    PHOTO: Remove the back panel from the dryer.

    PHOTO: Remove the back panel from the dryer.

  3. 03.

    Remove the fuse

    Pull the wires off of the thermal fuse. Remove the mounting screw using a 1/4" nut driver. Pull the fuse off of the blower housing.

    PHOTO: Remove the wires from the thermal fuse.

    PHOTO: Remove the wires from the thermal fuse.

    PHOTO: Remove the thermal fuse mounting screw.

    PHOTO: Remove the thermal fuse mounting screw.

  4. 04.

    Install the new thermal fuse

    Position the new fuse and secure it with the screw. Push the wires onto the connection spades on top of the new thermal fuse. It doesn’t matter which wire goes into which terminal on the thermal fuse.

  5. 05.

    Reattach the back panel

    Position the back panel on the back of the dryer. Line up the mounting screw holes. Insert the mounting screws and tighten them firmly.

  6. 06.

    Plug in the dryer

    Plug the dryer into the wall outlet to restore electrical power.

  7. 07.

    Clean the exhaust vent

    To prevent the thermal fuse from blowing again soon, remove the flexible vent in the back of the dryer and clean the inside of the flexible vent hose. Clean the air duct going to the outside of your home with a duct cleaning brush. Vacuum the area to clean up dust. 

Warning: Undertaking repairs to appliances can be hazardous. Use the proper tools and safety equipment noted in the guide and follow all instructions. Do not proceed until you are confident that you understand all of the steps and are capable of completing the repair. Some repairs should only be performed by a qualified technician.

Most common symptoms to help you fix your dryers

Choose a symptom to see related dryer repairs.

Main causes: bad gas valve coils, broken heating element, tripped safety thermostat or fuse, bad operating thermostat, c…

Main causes: bad timer or electronic control board, door switch failure…

Main causes: lack of electrical power, bad power cord, wiring failure, bad control board, blown thermal fuse, bad door s…

Main causes: clogged exhaust vent, bad motor relay, loose dryer door catch, bad door switch, control system failure, fau…

Main causes: damaged door strike, worn door catch…

Main causes: bad drum support roller, damaged idler pulley, broken blower fan blade, worn drum glide bearing, bad drive …

Main causes: clogged exhaust system, heating system failure, deposits on moisture sensor, control system failure…

Main causes: door switch failure, lack of power, broken belt, blown thermal fuse, bad drive motor, control system failur…

Most common repair guides to help fix your dryers

These step-by-step repair guides will help you safely fix what’s broken on your dryer.

How to replace a thermal fuse in an electric dryer

How to replace a thermal fuse in an electric dryer

When the air in the dryer overheats—usually because the vent is clogged—the thermal fuse blows, stopping the dryer. You …

Repair difficulty
Time required
 15 minutes or less
How to install a thermal cut-off fuse kit in an electric dryer

How to install a thermal cut-off fuse kit in an electric dryer

The thermal cut-off fuse shuts off the heat if the dryer overheats when the high-limit thermostat fails. Install a ther…

Repair difficulty
Time required
 15 minutes or less
How to replace a dryer door switch

How to replace a dryer door switch

The dryer won't start if the door switch isn't working correctly. You can install a replacement dryer door switch in les…

Repair difficulty
Time required
 15 minutes or less

Effective articles & videos to help repair your dryers

Use the advice and tips in these articles and videos to get the most out of your dryer.

How to use your clothes dryer efficiently

How to use your clothes dryer efficiently

Get expert tips on using your dryer efficiently to save energy.…

How to clean and maintain your clothes dryer

How to clean and maintain your clothes dryer

Get expert DIY tips and advice for keeping your clothes dryer in top shape with cleaning and maintenance.…

Top questions about Sears and Sears PartsDirect

Top questions about Sears and Sears PartsDirect

Get answers to frequently asked questions about Sears and Sears PartsDirect.…