How to replace the direct-drive motor on a front-load washer
This washer repair guide explains how to install a new drive motor in a direct-drive front load washer. This type of washer doesn't have a drive belt; the drive motor attaches directly to the spin basket shaft. If the direct drive motor fails, the washer basket won't spin. The control panel usually displays an error code if the drive motor fails. For example, a failed direct drive motor in an LG or Kenmore front-load washer typically causes the control to display the LE error code.
Follow the steps in this washer repair guide to replace a failed direct drive motor with a manufacturer-approved washer part.
If you're not sure if your washer has a direct-drive motor, check out the explanation in our washer FAQs.
This repair procedure covers direct-drive, front-load washers made by Kenmore and LG. You also can use the same basic procedure to replace the direct-drive motor in Samsung, Whirlpool, Maytag and Amana front-load washers.
Instructions
- 01.
Shut off the electricity
Unplug the power cord from the wall outlet.
Wear work gloves to protect your hands.
Have someone help you move the washer away from the wall.
- 02.
Remove the back panel
Remove the 4 screws from the back panel.
Lift up to release the back panel and pull it off.
PHOTO: Remove the screws from the washer rear panel.
PHOTO: Remove the washer back panel.
- 03.
Remove the rotor
Remove the 17mm bolt on the back of the motor and pull the rotor off of the motor.
Tip: Hold the rotor still and strike the ratchet with a sharp blow to loosen the rotor bolt.
PHOTO: Remove the bolt from the motor.
PHOTO: Remove the rotor from the motor.
- 04.
Release the wire harness from the tub
Use a Phillips screwdriver to remove the screws from the wire harness bracket and retainers on the back of the washer tub.
Remove the screw that holds the green ground wire on the back of the tub.
PHOTO: Release the wire harness from the tub.
- 05.
Remove the stator
Remove the 6 bolts that secure the stator—the part of the motor that doesn't move—to the tub.
Release the stator and unplug the wire harness connections.
Remove the motor.
PHOTO: Remove the bolts that hold the stator to the tub.
PHOTO: Unplug the stator wire harness connections.
PHOTO: Remove the wires from the tachometer.
- 06.
Install the new motor
Connect the wires to the motor and the tachometer.
Position the new stator on the back of the tub.
Replace the 6 bolts and tighten them firmly.
- 07.
Reattach the wire harness
Reinstall the wire harness bracket and retainers that secure the wires to the back of the tub.
Attach the green ground wire to the tub.
- 08.
Reinstall the rotor
Push the rotor back onto the shaft.
Apply thread locking fluid to the bolt.
Reinstall the bolt and tighten it firmly.
Tip: Open the washer door and have someone hold the spin basket still from the front of the washer while you firmly tighten the rotor bolt. - 09.
Reinstall the rear panel
Position the rear panel on the back of the washer and secure it with the mounting screws. Tighten the screws firmly.
- 10.
Restore the power
Plug the washer into the electrical outlet. Return the washer to its original location.
Most common symptoms to help you fix your washers
Choose a symptom to see related washer repairs.
Main causes: broken lid switch or lid lock, bad pressure switch, broken shifter assembly, faulty control system…
Main causes: lack of electrical power, wiring failure, bad power cord, electronic control board failure, bad user interf…
Main causes: leaky water inlet valve, faulty water-level pressure switch, bad electronic control board…
Main causes: water heater failure, bad water temperature switch, faulty control board, bad water valve, faulty water tem…
Main causes: no water supply, bad water valves, water-level pressure switch failure, control system failure, bad door lo…
Main causes: worn agitator dogs, bad clutch, broken motor coupler, shifter assembly failure, broken door lock, suspensio…
Main causes: unbalanced load, loose spanner nut, worn drive block, broken shock absorber or suspension spring, debris in…
Main causes: clogged drain hose, house drain clogged, bad drain pump, water-level pressure switch failure, bad control b…
Main causes: bad lid switch or door lock, bad timer or electronic control board, wiring failure, bad water inlet valve a…
Repair guides for front-load washers
How to replace a water inlet valve on a front-load washer
The water valve assembly is the gatekeeper for water entering your front-load washer. You can replace it yourself, follo…
How to replace a motor control board on a front-load washer
The motor control board makes sure the motor spins in the right direction and at the right speed. You can install a new …
How to replace the user interface board in a front-load washer
Follow these steps to replace the user interface board in your front-load washer if the buttons or lights are broken.…
Effective articles & videos to help repair your washers
Use the advice and tips in these articles and videos to get the most out of your washer.
Find tips for using your washing machine efficiently to save energy and help reduce utility bills.…
Learn about all the convenient features on our Sears PartsDirect website that make your parts purchases easier.…
Get answers to frequently asked questions about Sears and Sears PartsDirect.…