How to replace the lid switch in a direct-drive top-load washer
This DIY washer repair guide explains how to replace the lid switch in a top-load washer. The lid switch is a safety device that prevents the washer from going into spin mode when the lid is open. If the lid switch doesn't work, the washer won't spin even when closed. Replace the lid switch with a manufacturer-approved washer part.
Use this repair procedure to replace the lid switch in Kenmore, Whirlpool, Maytag, Roper, Estate and Crosley top-load washers.
We also have instructions for replacing the lid switch/lock on a VMW top-load washer. If you're not sure if your top-load washer has VMW technology, check out our washer FAQsto see how you can tell.
This video explains how to replace the lid switch on a direct-drive top-load washer.
Instructions
- 01.
Shut off the electricity
Unplug the power cord from the wall outlet.
Wear work gloves to protect your hands.
- 02.
Open the control console
Pull the plastic end caps off the sides of the control console.
Remove the screws at the base of the control console.
Pull the control console slightly forward and then swing it up and over the top of the back panel.
PHOTO: Remove the control panel endcaps.
PHOTO: Remove the screws at the base of the control panel.
PHOTO: Open the control panel by pulling it slightly forward and then swinging it up and back.
- 03.
Remove the cabinet
Unplug the wire harness from the lid switch on the washer’s top panel.
Release the clips that secure the cabinet to the washer’s back panel. Using a slot screwdriver, pry the clips forward to release them from the slots in the top panel.
Lift the back of the cabinet and slide the cabinet forward to remove it from the washer frame.
PHOTO: Unplug the wire harness from the lid switch.
PHOTO: Release the clips that hold the cabinet to the back panel.
PHOTO: Slide the cabinet forward and remove it from the frame.
- 04.
Remove the lid switch
Press in on the lid switch wire harness plug locking tabs to release them and then pull the plug out of the top cabinet panel.
Release the green ground wire by removing the screw that secures it to the cabinet.
Remove the lid switch mounting screws.
Release the lid switch wire harness from the clips and pull the lid switch out of the cabinet.
PHOTO: Pull out the lid switch wire harness plug.
PHOTO: Remove the green ground wire from the washer cabinet.
PHOTO: Remove the lid switch mounting screws.
PHOTO: Remove the lid switch from the cabinet.
- 05.
Install the new lid switch
Position the new lid switch in the cabinet and reinstall the mounting screws.
Insert the lid switch wire harness into the harness clips and snap the wire harness plug into the cabinet top panel.
Reconnect the green ground wire using the mounting screw.
PHOTO: Install the lid switch mounting screws.
PHOTO: Install the lid switch wire harness plug.
PHOTO: Connect the green ground wire to the cabinet.
- 06.
Reinstall the cabinet
Position the cabinet in front of the washer.
Tilt the back of the cabinet up slightly and keep the front lip of the cabinet on the floor. To position the front lip under the washer frame, push the base of the cabinet forward with your foot to slide the front lip of the cabinet under the front base of the washer. Then lower the back of the cabinet so the alignment tabs at the back sides of washer base fit into the holes on the back sides of the cabinet.
Reinstall the spring clips at the top of the cabinet.
Plug the lid switch wire harness back into the receptacle on the top panel of the washer.
PHOTO: Reinstall the washer cabinet.
PHOTO: Engage the rear cabinet tabs.
PHOTO: Reinstall the spring clips at the top of the cabinet.
PHOTO: Plug in the lid switch wire harness back into the receptacle.
- 07.
Reinstall the control console
Flip the control console down and position it properly on the top panel of the washer.
Reinstall the mounting screws at the base of the control console.
Snap the plastic end caps onto the sides of the control console.
PHOTO: Flip the control panel down and close the console.
PHOTO: Reinstall the control console mounting screws.
PHOTO: Reinstall the control panel endcaps.
- 08.
Restore the power
Plug the washer into the electrical outlet.
Most common symptoms to help you fix your washers
Choose a symptom to see related washer repairs.
Main causes: unbalanced load, loose spanner nut, worn drive block, broken shock absorber or suspension spring, debris in…
Main causes: bad lid switch or door lock, bad timer or electronic control board, wiring failure, bad water inlet valve a…
Main causes: clogged drain hose, house drain clogged, bad drain pump, water-level pressure switch failure, bad control b…
Main causes: leaky water inlet valve, faulty water-level pressure switch, bad electronic control board…
Main causes: water heater failure, bad water temperature switch, faulty control board, bad water valve, faulty water tem…
Main causes: lack of electrical power, wiring failure, bad power cord, electronic control board failure, bad user interf…
Main causes: no water supply, bad water valves, water-level pressure switch failure, control system failure, bad door lo…
Main causes: worn agitator dogs, bad clutch, broken motor coupler, shifter assembly failure, broken door lock, suspensio…
Main causes: broken lid switch or lid lock, bad pressure switch, broken shifter assembly, faulty control system…
Repair guides for top-load washers
How to replace the clutch assembly in a top-load washer
If the washer spins when the basket is empty but not when the basket is full, the problem could be the clutch assembly. …
How to replace the motor coupler on a top-load washer
If the washer drains but won’t agitate or spin, the motor coupler might have broken to protect the drive motor from dama…
How to replace the gear case in a top-load washer
If the washer won't spin or agitate with the motor running, replace the gear case, following the steps in this repair gu…
Effective articles & videos to help repair your washers
Use the advice and tips in these articles and videos to get the most out of your washer.
Find tips for using your washing machine efficiently to save energy and help reduce utility bills.…
Learn about all the convenient features on our Sears PartsDirect website that make your parts purchases easier.…
Get answers to frequently asked questions about Sears and Sears PartsDirect.…