$8.07
|Â 11% OFF Phone Price : $9.07
CONFIRM THE PART FITS
Part Information
This auger bearing (part number 9517MA) is for snowblowers.
Wear work gloves to protect your hands when installing this part.
Frequently Used Together
- $12.09|Â14% OFF Phone Price : $14.09
- $8.57|Â10% OFF Phone Price : $9.57
- $16.28|Â11% OFF Phone Price : $18.28
- $7.49|Â12% OFF Phone Price : $8.49
- $278.79|Â$12.00 OFF Phone Price : $290.79
- $10.62|Â16% OFF Phone Price : $12.62
- $6.42|Â13% OFF Phone Price : $7.42
- $29.80|Â17% OFF Phone Price : $35.80
Top models using the same part
| Model Name | Model Number | Diagram Name |
|---|---|---|
| Model #DP826E585317 Noma gas snowblower | DP826E585317 | Auger housing assembly |
| Model #G2254010 Canadiana gas snowblower | G2254010 | Auger housing assembly |
| Model #G2254010 Dynamark gas snowblower | G2254010 | Auger housing assembly |
| Model #G2254010 Signature gas snowblower | G2254010 | Auger housing assembly |
| Model #624508X4B Murray gas snowblower | 624508X4B | Auger housing |
| Model #624604X35 Murray gas snowblower | 624604X35 | Auger housing |
| Model #624604X81 Murray gas snowblower | 624604X81 | Auger housing |
| Model #536887250 Craftsman gas snowblower | 536887250 | Auger housing |
| Model #536887992 Craftsman gas snowblower | 536887992 | Auger housing |
| Model #536887251 Craftsman gas snowblower | 536887251 | Auger housing |
Reviews
Perfect fit
It was a fairly straightforward installation. I would add that greasing them might be a valuable part of the instructions
VinnyI, Staten Island, NY
Did you find this review helpful?
- Ease of Installation
- Easy
- Duration of Installation
- 30 minutes - 1 hour
Yes, I would recommend this to a friend
QUICK & EASY
One may find the part a little cheaper But, one will receive their part quickly & it will be the correct one with searspartsdirect Putting the part in was easy with the aid of a clamp that can be reset into an expander These are really not bearings as much as they are bushings to hold the ends of the auger. Probably would be good to order a couple of pairs if you plan on keeping the snowblower. DO NOT OVER TIGHTEN and a washer would help to disperse the load to help prevent the plastic bearing/bushing from developing a crack. Some blue loctite on the threads, too.
Stepside, Stillwater, NJ
Did you find this review helpful?
- Ease of Installation
- Easy
- Duration of Installation
- 30 minutes - 1 hour
Yes, I would recommend this to a friend
AUGER BEARING EASY TO INSTALL
The Bearing was easy to install when I had to remove the blade. Always check the auger bearing when changing out the belt. I noticed the bearings were cracked at the mounting holes, probably from age/cold weather.
snowblower, nj
Did you find this review helpful?
- Ease of Installation
- Very Easy
- Duration of Installation
- 1 - 2 hours
Yes, I would recommend this to a friend
Easily installed
Easy to install. Just like new again and right on time!
Phil, New Haven
Did you find this review helpful?
- Ease of Installation
- Easy
- Duration of Installation
- 30 minutes - 1 hour
Yes, I would recommend this to a friend
Plastic, should have been made by metal!
Horrible to install! Shear pin got wedged in shaft! Caused flange to break! Flange should have been made of metal. My fault, I hit a rock! But snowblower, over all, has been a good one! But, I won't buy another, with a plastic flange!
Butch, Westernport Md.
Did you find this review helpful?
- Ease of Installation
- Very Difficult
- Duration of Installation
- More than 2 hours
Yes, I would recommend this to a friend
Easy to modify and install
These bearings replaced two cracked bearings that would have cost me $20 to replace OEM. I chose these and modified the mounting holes to fit the housing. These are made of high strength plastic that won't wear/fail easily and seem far more robust than the OEM Snapper parts that I used these to replace.
SvenSvensen, Bountiful, UT
Did you find this review helpful?
- Ease of Installation
- Very Easy
- Duration of Installation
- Less than 30 minutes
Easy to install.
Had to replace the part on my snowblower because it wasn'the running properly.
Jayhawks, New jersey
Did you find this review helpful?
- Ease of Installation
- Very Difficult
- Duration of Installation
- 30 minutes - 1 hour
Installation
Three nuts / bolts each side, tipped blower back on handles, used milk crate for support, pry bar to give room to slip bearings off....may have been more difficult if blower was new.....but then would not have needed bearings,,,,easy peezie
Papaommalmal, North Pole,Alaska
Did you find this review helpful?
- Ease of Installation
- Very Easy
- Duration of Installation
- 30 minutes - 1 hour