April 01, 2013

How to install a pressure washer chemical injection kit

How to install a pressure washer chemical injection kit

This DIY repair guide explains how to replace a pressure washer chemical injection valve. The chemical injection valve draws detergent into the pump when you use a low-pressure nozzle for cleaning. A worn or damaged chemical injection valve won’t pull detergent into the water stream. If the pressure washer isn't spraying soapy water when it should, first make sure you’re using a low-pressure nozzle and the siphon hose isn’t clogged. If so, replace the damaged chemical injection valve with the manufacturer-approved replacement kit. The chemical injection kit includes the O-ring and all parts needed for the repair.

Follow the steps in this repair guide to install the chemical injection kit in common Craftsman, Generac, Briggs & Stratton, Husqvarna and Troybilt pressure washers.

Quick links
Tools required
Metric wrench set
Silicone lubricant
Torque wrench (optional)
Work gloves
Repair difficulty
Time required
15 minutes or less
Repair difficulty
Time required
15 minutes or less

Instructions

  1. 01.

    Disconnect the spark plug

    Disconnect the spark plug wire from the spark plug.

  2. 02.

    Remove the chemical injection valve

    If detergent is in the detergent reservoir, clamp the chemical injection hose near the chemical injection valve.

    Use an open-end wrench to turn the chemical injection valve counter-clockwise and remove it.

    PHOTO: Clamp off the chemical injection hose.

    PHOTO: Clamp off the chemical injection hose.

    PHOTO: Pull the chemical injection hose off of the valve.

    PHOTO: Pull the chemical injection hose off of the valve.

    PHOTO: Remove the chemical injection valve.

    PHOTO: Remove the chemical injection valve.

  3. 03.

    Install the new chemical injection valve

    Install the O-ring from the kit on the new chemical injection valve.

    Lubricate the O-ring with silicone lubricant. Thread the new chemical injection valve into the pump and tighten. Reconnect the chemical injection hose.

    Release the clamp from the chemical injection hose, if used.

    Tip: If you have a torque wrench, tighten the new chemical injection valve to 10-12 ft.-lbs. or torque.
    PHOTO: Install the new chemical injection valve.

    PHOTO: Install the new chemical injection valve.

    PHOTO: Reconnect the chemical injection hose.

    PHOTO: Reconnect the chemical injection hose.

  4. 04.

    Reconnect the spark plug

    Reconnect the spark plug wire to the engine.

  5. 05.

    Check pressure washer operation

    Start the pressure washer and check for leaks. Check for proper detergent draw through the new chemical injection valve.

Warning: Undertaking repairs to appliances can be hazardous. Use the proper tools and safety equipment noted in the guide and follow all instructions. Do not proceed until you are confident that you understand all of the steps and are capable of completing the repair. Some repairs should only be performed by a qualified technician.

Symptoms for gas pressure washers

Choose a symptom to see related pressure washer repairs.

Main causes: using a high-pressure spray tip when applying detergent, clogged siphon tube, chemical injection system fai...

Main causes: overfilling engine with oil, improper fuel/air mixture, choke system problems, dirty carburetor, engine nee...

Main causes: broken recoil spring, damaged recoil starter...

Main causes: dirty air filter, stale fuel, clogged or dirty carburetor, bad unloader valve...

Main causes: insufficient water supply, clogged water inlet screen, clogged pressure hose, faulty pump check valves, stu...

Main causes: damaged recoil starter, oil inside cylinder, locked up engine piston...

Main causes: faulty unloader valve, bad pressure regulator...

Main causes: stale fuel, gummed up carburetor, engine needs tune up, throttle and choke controls need adjustment, bad re...

Main causes: pump running for more than 5 minutes when the spray wand isn't being used, faulty pressure relief valve, ba...

Repair guides for gas pressure washers

These step-by-step repair guides will help you safely fix what’s broken on your pressure washer.

How to install a pressure washer check valve kit

How to install a pressure washer check valve kit

Air in the inlet water supply can damage the check valves. If the pump won’t build up pressure due to damaged check valv...

Repair difficulty
Time required
120 minutes or less
How to install a pressure washer O-ring kit

How to install a pressure washer O-ring kit

O-rings seal fittings on the pressure washer pump. Damaged seals allow water to leak from the pump. Follow these steps t...

Repair difficulty
Time required
45 minutes or less
How to install a pressure washer chemical injection kit

How to install a pressure washer chemical injection kit

The chemical injection valve draws detergent into the pump. If it’s not drawing detergent, use a repair kit to replace t...

Repair difficulty
Time required
15 minutes or less

Effective articles & videos to help repair your pressure washers

Use the advice and tips in these articles and videos to get the most out of your pressure washer.

How to enjoy all the online benefits we offer on our Sears PartsDirect website

How to enjoy all the online benefits we offer on our Sears PartsDirect website

Learn about all the convenient features on our Sears PartsDirect website that make your parts purchases easier....

Tapping into a new feature in the Search Bar on Sears PartsDirect

Tapping into a new feature in the Search Bar on Sears PartsDirect

Learn about a new feature added to the Search Bar on Sears PartsDirect...

Top questions about Sears and Sears PartsDirect

Top questions about Sears and Sears PartsDirect

Get answers to frequently asked questions about Sears and Sears PartsDirect....