How to replace a freestanding ice maker cutter grid
This DIY repair guide explains how to replace the cutter grid in a freestanding ice maker. The cutter grid has thin, heated wires that slice the slab of ice on the evaporator plate into ice cubes that fall into the bin. When the cutter grid breaks, the ice slabs can stack up, and ice production stops. Replace the broken cutter grid with the manufacturer-approved freestanding ice maker part.
These steps show how to replace the cutter grid in Kenmore, Whirlpool, KitchenAid, Maytag, GE and JennAir freestanding ice makers.
Instructions
- 01.
Disconnect power
Remove any ice that is in the storage bin of the ice maker and store it in a separate container during this repair.
Cover the drain hole in the ice bin with a cloth to prevent hardware from falling inside.
Unplug the ice maker or shut off the house circuit breaker to disconnect electrical power.
- 02.
Remove the cutter grid cover
Open the ice maker door and remove the screws from the bottom of the cutter grid cover.
Pull the cutter grid cover out and set it aside.
Remove any uncut slabs of ice from the top of the cutter grid.
PHOTO: Remove the cutter grid cover screws.
PHOTO: Remove the cutter grid cover.
- 03.
Remove the cutter grid
Remove the hex-head mounting screws from both sides of the cutter grid.
Pull the cutter grid down slightly to access the cutter grid wire harness connection.
Disconnect the cutter grid wire harness connector from the bottom of the control housing.
Pull the cutter grid out of the ice maker.
PHOTO: Remove the cutter grid mounting screws.
PHOTO: Unplug the cutter grid wire harness.
PHOTO: Remove the cutter grid.
- 04.
Install the new cutter grid
Push the new cutter grid into the ice maker and plug the cutter grid wire harness into the connector in the bottom of the control housing.
Line up the mounting screw holes and reinstall the hex-head mounting screws.
PHOTO: Plug in the cutter grid wire harness.
- 05.
Reinstall the cutter grid cover
Position the cutter grid cover in front of the cutter grid and secure it with the mounting screws.
PHOTO: Reinstall the cutter grid cover.
- 06.
Restore power
Plug the ice maker into the wall outlet or reset the house circuit breaker to restore power.
- 07.
Fill the ice storage bin
Remove the cloth that was used to cover the drain hole in the ice storage bin.
Fill the ice bin with ice that was stored in a separate container during this repair.
Note: If you need help completing this repair on a Frigidaire ice maker, schedule [Frigidaire ice machine repair](https://www.searshomeservices.com/repair/frigidaire/ice-maker-freestanding) and we'll send a service technician to your home to fix the problem.
Most common symptoms to help you fix your freestanding ice makers
Choose a symptom to see related ice maker repairs.
Main causes: failing compressor, bad condenser fan motor, faulty drain pump, bad recirculation pump, water supply proble…
Main causes: dirty evaporator plate, untreated water supply, food items being stored in ice storage bin…
Main causes: wiring failure, broken cutting grid, faulty electronic control board…
Main causes: bad electronic control board, water supply problems, faulty recirculation pump, sealed system failure, brok…
Main causes: cracked water supply line, leaky drain line, broken drain pump, cracked water reservoir, leaky ice bin…
Main causes: bad bin thermistor, condenser fan failure, faulty control board…
Main causes: water supply problems, control board failure, weak recirculation pump, clogged water distributer, faulty cu…
Main causes: lack of electrical power, bad power cord, wiring failure, bad control board, faulty bin thermistor, bad eva…
Most common repair guides to help fix your freestanding ice makers
These step-by-step repair guides will help you safely fix what’s broken on your ice maker.
How to replace a freestanding ice maker recirculation pump
If your ice maker isn’t making ice, the pump could be the problem. Here’s how to replace it. …
How to replace a freestanding ice maker electronic control board
When the electronic control board won’t activate the ice maker components, follow these steps to install a new one.…
How to replace a freestanding ice maker cutter grid
When the cutting grid is broken, ice cubes don’t drop into the ice bin. Use the steps in this repair guide to replace a…
Effective articles & videos to help repair your freestanding ice makers
Use the advice and tips in these articles and videos to get the most out of your ice maker.
Learn about all the convenient features on our Sears PartsDirect website that make your parts purchases easier.…
Get answers to frequently asked questions about Sears and Sears PartsDirect.…
See what troubleshooting steps to take with your freestanding ice maker before calling for repair.…