September 08, 2020

How to replace an electronic control board in an electric dryer

This step-by-step dryer repair guide shows how to replace the electronic control board in an electric dryer.

You may need to replace the control board if the dryer won't power up even though you already checked the circuit breaker. You may also need to replace the electronic control board if the dryer powers up but won't start even though the door switch is working and the thermal fuse isn't blown.

Because the electronic control board manages all of the dryer's components and controls the dryer cycle times, it's difficult to pinpoint the control board as the source of a problem. Unless you see obvious damage to the control board or you've definitely determined that the control board failed, have a local dryer repair expert do advanced diagnostic tests before replacing the dryer control board with a manufacturer-approved dryer part.

Use this procedure to replace the electronic control board in many Kenmore, Frigidaire and Electrolux electric dryers. You also can use the same basic steps to replace the electronic control board in some Whirlpool, Maytag, Amana, Samsung, LG and GE dryers.

If you have a gas dryer, replace the electronic control board following this repair guide and video.

Quick links

Video

Instructions

Tools required

1/4-inch nut wrench

Small slot screwdriver

Vacuum

Work gloves

Ground strap (optional)

Repair difficulty

Time required

45 minutes or less

How to replace an electric dryer electronic control board

Replacing an electronic control board in an electric dryer.

Instructions

01.
Shut off the power
Unplug the dryer.
02.
Remove the top panel
Slide the dryer away from the wall. On the back of the dryer, locate the two hex-head screws that secure the top panel to the frame. Remove the screws using a 1/4-inch nut driver.
Pull the top panel back slightly to release the tabs behind the console. Pull the top panel up and off of the dryer.
Tip: While you have the dryer open, vacuum the dust and lint from inside the dryer.
PHOTO: Remove the screws from the back of the dryer top panel.
PHOTO: Release the tabs behind the front console.
PHOTO: Pull the top panel up and off the dryer.
03.
Remove the electronic control board
Take a digital picture of the wiring connections so you can connect the new control board correctly.
Using a slot screwdriver, release the locking tabs from the wire connectors. Pull the wire harness plug from the connection receptacle on the electronic control board.
Remove the single hex head screw with a 1/4-inch nut driver. Slide the electronic control board to release it from the support bracket slots. Set the electronic control board aside for disposal.
Tip: With some units, the wire harness has enough slack to let you detach connections one at a time and immediately attach them to the new control board—a sure way to get the connections right.
PHOTO: Release the locking tabs on the control board wire harness connectors.
PHOTO: Remove the control board mounting screw.
PHOTO: Remove the control board from the support bracket.
04.
Install the new electronic control board
Before removing the new control board from the package, touch metal on the dryer to dissipate static electricity.
Position the new control board on the support bracket and push it into the mounting slots. Lock it into place so it lines up the mounting screw hole. Replace the mounting screw. Avoid overtightening by turning the screw with the nut driver until it stops and then give the screw one firm twist to snug it in place.
Tip: If you have a grounding strap, put it on and clip the lead to metal on the dryer before touching the new control board.
05.
Connect the wires
Using your digital photo as a guide, connect the wires to the new electronic control board. Push the wire harness plug until its locking tab snaps into place. The plugs fit together only one way; if they aren't fitting together easily, reorient them. Never force the plugs into place.
Warning: Connecting the wires incorrectly can damage dryer components. If you’re unsure about the connections, have a service technician complete the repair.
06.
Reinstall the top panel
Place the panel on the top of the dryer and position it slightly away from the tabs behind the control panel. Push the panel forward to engage the tabs. Work the panel into place and replace the mounting screws at the back of the dryer.
07.
Restore the power
Plug the dryer into the wall outlet.

Warning: Undertaking repairs to appliances can be hazardous. Use the proper tools and safety equipment noted in the guide and follow all instructions. Do not proceed until you are confident that you understand all of the steps and are capable of completing the repair. Some repairs should only be performed by a qualified technician.